- 您现在的位置：买卖IC网 > Sheet目录1229 > MAX9652EVKIT+ (Maxim Integrated Products)EVAL KIT FOR MAX9652
MAX9652 Evaluation Kit
Quick Start
Recommended Equipment
Before beginning, the following equipment is needed:
? 3.3V DC power supply (VDD) capable of 50mA
? Video signal generator (e.g., Tektronix TG-700 or similar)
? The appropriate video measurement equipment
(e.g., Tektronix VM5000)
Procedure
The MAX9652 EV kit is fully assembled and tested.
Follow the steps below to verify board operation:
1) Connect the outputs of the video signal generator to
the Y_INPUT, PB_INPUT, and PR_INPUT BNC con-
nectors on the MAX9652 EV kit.
2) Connect the Y_OUTPUT, PB_OUTPUT, AND
PR_OUTPUT BNC connectors on the EV kit to the
input of the video measurement equipment.
3) Connect the power-supply ground to the GND pad
on the EV kit.
4) Connect the 3.3V supply to the VDD pad on the EV kit.
5) Set the video signal generator for the desired video
input signals.
6) Turn on the power supply and enable the video sig-
nal generator.
7) Analyze the video output signal.
Detailed Description of
Hardware
The MAX9652 EV kit is a fully assembled and tested
surface-mount PCB that contains the MAX9652 triple-
channel, video-filter amplifier and buffer for HDTV appli-
cations. The MAX9652 filter has ±1dB passband out to
42MHz and 50dB attenuation at 109MHz. The
MAX9652 EV kit has three input channels to accept a
full set of component video input signals.
The MAX9652 EV kit uses 0.1μF ceramic capacitors to
AC-couple the video input signals to the MAX9652. The
input capacitor stores a DC level such that the outputs
are clamped to the appropriate DC voltage level. All
video inputs have a 75 Ω termination to ground. The
MAX9652 EV kit video outputs can be DC- or AC-cou-
pled. By default, 0 Ω resistors are installed on R7, R8,
R9, and C4, C7, and C8 are open; each of the outputs
are configured to drive DC-coupled video loads. To
configure the outputs to drive the AC-coupled video
loads, remove R7, R8, and R9, and install the 220μF
capacitors on C4, C7, and C8.
2
_______________________________________________________________________________________
发布紧急采购，3分钟左右您将得到回复。
相关PDF资料
MAX9660EVKIT+
EVALUATION KIT FOR MAX9660
MAX9670EVKIT+
EVALUATION KIT FOR MAX9670
MAX9671EVKIT+
EVALUATION KIT FOR MAX9671
MAX9694EVKIT+
EVAL KIT FOR MAX9694
MAX97003EVKIT#
EVAL KIT MAX97003
MAX97220AEVKIT+
EVAL KIT
MAX9725EEVKIT+
KIT EVAL FOR MAX9725
MAX9736AEVKIT+
KIT EVAL FOR MAX9736A
相关代理商/技术参数
MAX9653AUB+
功能描述:视频放大器 3.3V HD/SD 3Ch Filter Amp RoHS:否 制造商:ON Semiconductor 通道数量:4 电源类型: 工作电源电压:3.3 V, 5 V 电源电流: 最小工作温度: 最大工作温度: 封装 / 箱体:TSSOP-14 封装:Reel
MAX9653AUB+T
功能描述:视频放大器 3.3V HD/SD 3Ch Filter Amp RoHS:否 制造商:ON Semiconductor 通道数量:4 电源类型: 工作电源电压:3.3 V, 5 V 电源电流: 最小工作温度: 最大工作温度: 封装 / 箱体:TSSOP-14 封装:Reel
MAX9653EVKIT+
功能描述:放大器 IC 开发工具 MAX9653 Eval Kit RoHS:否 制造商:International Rectifier 产品:Demonstration Boards 类型:Power Amplifiers 工具用于评估:IR4302 工作电源电压:13 V to 23 V
MAX9654AUB+
功能描述:视频放大器 3.3V HD/SD 3Ch Filter Amp RoHS:否 制造商:ON Semiconductor 通道数量:4 电源类型: 工作电源电压:3.3 V, 5 V 电源电流: 最小工作温度: 最大工作温度: 封装 / 箱体:TSSOP-14 封装:Reel
MAX9654AUB+T
功能描述:视频放大器 3.3V HD/SD 3Ch Filter Amp RoHS:否 制造商:ON Semiconductor 通道数量:4 电源类型: 工作电源电压:3.3 V, 5 V 电源电流: 最小工作温度: 最大工作温度: 封装 / 箱体:TSSOP-14 封装:Reel
MAX9654EVKIT+
功能描述:放大器 IC 开发工具 MAX9654 Eval Kit RoHS:否 制造商:International Rectifier 产品:Demonstration Boards 类型:Power Amplifiers 工具用于评估:IR4302 工作电源电压:13 V to 23 V
MAX9655AEE+
功能描述:视频开关 IC Video Switch f/Dual SCART Connector RoHS:否 制造商:Texas Instruments 开关数量:4 开启电阻（最大值）:12 Ohms 传播延迟时间: 开启时间（最大值）: 关闭时间（最大值）: 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:WQFN-42 封装:Reel
MAX9655AEE+T
功能描述:视频开关 IC Video Switch f/Dual SCART Connector RoHS:否 制造商:Texas Instruments 开关数量:4 开启电阻（最大值）:12 Ohms 传播延迟时间: 开启时间（最大值）: 关闭时间（最大值）: 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:WQFN-42 封装:Reel